Fans: Data Sheet Installation guide
Model / Packing list
| Specs
| Mounting
| Power
| On/Off
Switch
| Smart
timer
Control
| Speed control
| Rough in box (4)
| Delta 120 vac
model
|
ATXFAN 50-12v
| 50 CFM, 4 inch depth
3 inch duct
| Wall, Ceiling
| 12v
| RV 12v
| DR2
| yes
8-12v
| SLM-A | SLM50
|
ATXFAN 70-48v
| 70 CFM, 4 inch depth
3 inch duct | Wall, Ceiling | 48v
| ATX 48v
| DR2C
| yes
25-44v
| SLM-A | SLM70
|
ATXFAN 70-PoE
| 70 CFM, 4 inch depth
3 inch duct | Wall, Ceiling | PoE 803.2af
|
|
| no
| SLM-A | SLM70
|
ATXFAN 70-12v
| 70 CFM, 4 inch depth
3 inch duct | Wall, Ceiling | 12v
| RV 12v | DR2
| yes
8-12v
| SLM-A | SLM70
|
ATXFAN 80-48v
| 80 CFM, 5.75 inch depth
4 inch duct | Ceiling
| 48v | ATX 48v | DR2C
| yes
25-44v | ITG-A
| ITG80
|
ATXFAN 80-PoE
| 80 CFM, 5.75 inch depth
4 inch duct | Ceiling
| PoE 802.3af
|
|
| no
| ITG-A
| ITG80
|
ATXFAN 80-12v
| 80 CFM, 5.75 inch depth
4 inch duct | Ceiling
| 12v
| RV 12v | DR2
| yes
|
ITG-A | ITG80
|
ATXFAN 100-12v
| 100 CFM, 5.75 inch depth
4 inch duct | Ceiling | 12v
| RV 12v | DR2
| yes
|
| GBR100
|
ATXFAN 100s-12v
| 100 CFM, 4 inch depth
3 inch duct | Wall, Ceiling | 12v
| RV 12v | DR2
| yes
|
| SLM100
|
Rough In
ATXFAN 80 and ATXFAN 70 share the same motor assembly. ATXFAN 80 is 4 inch duct, 50 and 70 are 3 inch ducts
ATXFAN 50 and ATXFAN 70 share the same rough in box ( SLM-A) $17 on Amazon
Switch Controls for 12v fans with AL-WS-DR2
Wall Switch model
(Light Switch with Fan Output)
| Fan Switch
option
| Control
| Timers
| Speed Control
| Schedules
| Sensor
|
AL-WS-DR2 ( Light attached )
| AL-WS-M
| Momentary - press to start / extend
long press to turn off | yes
| DALI
control
| yes
| yes ( P023R6-M )
|
AL-WS-DR2 ( Light Attached )
| none
| Fan On/Off follows Light - or -
Fan Auto on if light stays on > 90 seconds
| yes -
delay after light goes off
| DALI
Control
| yes
| yes ( P023R6-M)
|
AL-WS-DR2 ( No Light Attached )
| none
| Momentary - press to start / extend
long press to turn off
| yes
| Slider
| yes
| see above
|
AL-WS-DR2
| Rocker
| ON - leave on to enable timers
Off - manually off, turn on as needed
| If ON
| DALI
Control
| yes
| yes ( P023R6-M) |
Switch Controls for 48v fans with AL-WS-DR2C
Wall Switch model
(Light Switch with Fan Output)
| Fan Switch
option
| Control
| Timers
| Speed Control
| Schedules
| Sensor
|
AL-WS-DR2C ( Light attached )
| AL-WS-M
| Momentary - press to start / extend
long press to turn off
| yes
| DALI
control
| yes
| yes ( P023R6-M) |
AL-WS-DR2C ( Light Attached )
| none
| Fan On/Off follows Light - or -
Fan Auto on if light stays on > 90 seconds
| yes -
delay after light goes off
| DALI
Control
| yes
| yes ( P023R6-M)
|
AL-WS-DR2C ( No Light Attached )
| none
| Momentary - press to start / extend
long press to turn off
| yes
| Slider
| yes
| see above
|
DR2 and 48v Exhaust fans
To use a 48v exhaust fan with the DR2 - do this:
- set the LED driver mode to Split
- set the N-Way mode to FAN
- set the Right channel to 48v
- connect a momentary switch to the N-Way input
this will operate the fan in one of these modes:
- with the light on, turn the fan one with the N-Way switch and do not turn it off manually - this will enable timer mode
- manual mode - turn the fan off manually one time, this will exit Timer mode until you enable it ( see above ) again.
- Follow mode - do not connect any N-Way switch - leave it open - the fan will be on when the light is on
- Timer without N-Way switch - jumper N-Way to ground - connect N-Way to ground
Uploading ....