Home / public / ... / AL - DALI - Pi / ZWD Control Suite / ZWD - Advanced

ZWD - Advanced

 
ZWD Advanced controls


ZWD provides some advanced controls for professional users



Query DALI POWER STATUS

this button returns the DALI voltages and currents

  • Internal power status  ( ON, OFF, Locked, low or high current)
  • Measured DALI bus voltage
  • DALI bus current when at logic zero
  • DALI bus current when at one to zero transition
  • DALI bus current  at logic one


Manual Address Assignment. 


enter the bus# (1 is default), Old Address, ,New Address and click Re-Assign.   ZWD will move the device and it's name to the new address.   DALI addresses are 0-63.   Thus,  if the new address is 255, then the device will be reset to no address, it can be found again using the assign address button. 
The bus# is only useful in 2 and 4 channel DALI systems
     
SEND DALI COMMANDS

You can send these DALI commands to the bus
  1. select the channel number ( for multi channel systems)
  2. Select the devices to send commands to
    1. Broadcast = ALL together
    2. Group ( 0 thru 15)
    3. Single Address ( 0-63 )
  3. Select the command to send
      1. Off, step up, step down, set to Min, set to Max
      2. go to scene
      3. set level
      4. set CCT
      5. Query Status
      6. Full individual rescan
      7. Reset to factory defaults ( keeping Short Address only)
Matrix of DALI addresses

  • Gray - never seen on the bus
  • Green - live at last quick scan
  • Yellow - duplicate devices at that address
  • Red - previously seen, not connected at this time
  • Tool Tip - popup shows the name of the device in the database


 Advanced


Image9


Advanced Controls for a device

you can

- Query a device with DALI 144 status command
- Read back all device data
- Send a DALI reset command 32 ( will also force re-calibration )
- Pulse one device to locate it
- Remove the short address assigned to the device, and / or remove it from the data base
 Image25
Internal DALI power supply options

you can enable / disable the internal DALI supply, and change the current supported

If you change from Auto to Locked - the values will be frozen, otherwise they are determined automatically ( if @ 80 mA, the DALI bus voltage is low - it will increase by 180 mA )

 Image27

Device Data Inspection

you can read back all technical details of the a DR2 with this command



Device Data Dump
Field description Cool Warm/Fan
Device Name Living Room DR2
UPC Code: [3, 4, 5, 6, 7, 8] 784099948190
FW Version: [9] 59
HW Version: [10] 3
Serial Number: [11, 12, 13, 14] 3276128581
N-Way Mode: [13] 3-Way
Uptime Hours: [3, 4] 423
On Time Hours: [5, 6] 1
kWh Hours total: [7, 8] 3
Average Watts Used: [9] 1
Peak Watts: [10] 26
UPS Mode: [11] disabled
kWh Hours 2: [12] 31
Real Time Wattage: [13] 0
Real Time Vinput: [14, 15] 48000
Real Time Watts: [18, 19]: [16, 17] 0 0
Primary Short Address: [0] 18
Main Transmit address: [1] send short address
Minimum brightness: [2] 1
Maximum brightness: [3] 254
Power on level: [4] last on/off
Fade Rate: [5] Up: 2, Down: 2
Output CV Target (Volts): [7]: [6] 56 56
Real Time CCT Level: [8] 2700
Driver LED mode: [9] CCT
CCT: [10]: [11] 5000 2712
Brightness if bus fails: [12] 1
Power on state: [14] Local
N-Way Switch Type: [16] Momentary
Main Switch type: [17] Momentary
DALI Secondary ARC level: [19] 0
Fan Hold Time, Minutes: [20] 10
Fan On Delay, Seconds: [21] 22
Fan Idle Target ( Volts ): [22] 0.0
Fan Running Target (Volts): [23] 11.938
Driver 30 mA threshold: [26, 27]: [24, 25] 700 680
Dim to Warm threshold: [28] 10
DALI Secondary Address : [29] 80
Slider location: [30] Left
Firmware Version: [31] 59
Driver 0 mA threshold: [34, 35]: [32, 33] 192 190
Minimum (mV): [38, 39]: [36, 37] 30576 30603
Full On count: [42, 43]: [40, 41] 690 710
LED Vth (Volts): [45]: [44] 30.0 30.0
Driver max (mA): [47]: [46] 666 666
Fan Status: [49] No Fan, , No Fan Detected, ,
Driver Status: [50]: [48] , , Off, LED Ok, , , , Off, LED Ok, , , 
30-660 mA threshold: [54, 55]: [52, 53] 80 80
Real Time Volts (mV): [58, 59]: [56, 57] 15274 13207
LED Effective mOhms / Rung: [70, 71]: [68, 69] 1030 1131
@ 660 mA (mV): [74, 75]: [72, 73] 37499 37771
CCT Fade rate: [76] 250
Secondary Address Fade Time: [77] 0
Adjust LED Vth - range is 1220 to 3770: [79]: [78] 2540 2540
Adjust Max current on Cool Value: [81]: [80] 848 848
Secondary minimum brightness: [82] 0
Secondary maximum brightness: [83] 254


    		 RSS of this page