ZWD - Devices

ZWD supports devices on the DALI bus with different features for each device.   These features are available after a DALI Master ( see the Admin page) has assigned addresses to DALI devices.

DALI devices are for example:

• ATX LED AL-WS-DR2 wall switch and LED Driver 
• ATX LED AL-WS-DALI-8B multi switch
  
• ATX LED AL-WS-010v DALI wall switch
  
  
• Sunricher SR-2303AC Triac driver for 120vac systems
  
• Sunricher SRP-2309-75CCT driver for tunable white up to 75 watts
• Meanwell DALI LED drivers like the ELG-100-24DA
  

  

Generic DALI Device management Device Name for the installer   'Public' Name for use with Hue/ Alexa/ Google/ Siri  Visible Checkbox ( used to hide rarely used items to reduce list size)   Group assignments ( see DALI instructions ) Wattage of the load for ZWD power calculations   FADE rate controls  ( duration and granularity )   Minimum DIM level - if the output is not off, this sets the  bottom of the dimming range  ( 1 is low, 254 is full bright )   Maximum DIM level, limit max level  ( 254 is full bright )   Power On level, brightness after power outage   Fail Level if the DALI bus has lost power Current Color temperature endpoint mapping of Color temperature and the DALI value for that color.   Also shown is the - DALI bus channel for multi bus systems ( 1 thru 4 ) - Short Address of this device - UPC and ID if reported if found - Firmware and Hardware version shown if readable - Factory set minimum dimming level
AL-WS-DR2 Additional Features    Not all advanced features are supported in early DR2 firmware versions  - only supported features are shown Fade UP time - # seconds to ON   Fade Down time - # seconds to OFF   Power ON level - either preset or simple return to the setting before power failed ( 254 is max).   Last means to set the light to the On/Off/Dim level prior to the power outage. Fail level - brightness if DALI bus is disconnected - 255 means no change  Driver mode.   There are these driver modes: Autodetect Split Left + Right ( typically used with Split N-Way) ALL CCT ALL Fixed Fan + Light Special PIR - Right output is powered all the time, an attached PIR device can be dimmed and controlled.   Changes in the PIR are detected and reported Fan + 12v DC CCT not found - CCT requested but not detected   2nd Split Address  ( Only useful if Split mode ) - this is the address that the Right output will have if N-Way mode is set to split   Slider Position - rightside up = bright, or leftside up = bright   Voltage ( Constant Voltage mode for Strip lights )
AL-WS-DR2 N-Way features   N-Way setting is at the bottom of the same page  - Three-Way - treats an external AL-WS-M as a 3-way switch Split - treats an external AL-WS-M a 2nd short address Fan Mode ( N-Way input controls the Fan) Night Mode ( future ) PIR Mode  ( future ) Vacancy ( future ) Auto Off mode - enables a timer to turn the light off after a delay
AL-WS-DR2 2nd Address features Split - treats an external AL-WS-M like a single button keypad Program that switch for the action you want Value = is the current setting ( 255 is disabled ) Address to send is the destination See DALI standards for Address,Group, Scene, Broadcast Trigger is an event that can be triggered by each button press Toggle is an event that can be triggered alternately On/Off by successive presses Undo is unique to ATX LED - if you enable Undo, then a Scene command is given, but if you hit that button again within 5 seconds, the lights will revert to the level before you hit scene - undo.
AL-WS-DR2 Fan features Fan Speed - 254 is max Fan Idle Speed - it can still turn when "off" - 0 disables this Delay between Light on and Fan on automatically Delay time to auto turn the fan off Note:  the AL-WS-M will turn the fan on/off as follows: Short press - on for 10 minutes (default - set by run time) Short press while on - add-on 5 minutes Long press - turns the fan off Note: FW 66-69 do not support fan only timeout - if there is just a fan, and no light, need to create a macro to turn the fan off automatically
AL-WS-DR2 Tunable White features   Color Temperature - slider to adjust the color temperature now   Temp / DALI Range - this changes the logical temperature associated with a DALI CCT value,  we default to 353 representing max Right current and 0 representing max Left current  Our default Right output has 2700K strings and the default Left output has 5000K strings.   Both can be edited.     Driver Mode must be ALL CCT for these controls to be active.   This is DT8 Voltage ( see DR2 general section above) Dim to Warm percentage - when the fixture is dimmed to this level ( default 1.5%) or 10 mA, the light will shift to warm   Color (raw) defines the physical connection of the strings to the two output drives.   In the event that the colors are discovered to be reversed on installation - this tab allows the colors to be reversed.
AL-WS-DR2 Advanced LED features The AL-WS-DR2 detects the topology of the attached LED fixtures. Each LED chip is 3 volts, multiple chips are arranged in series per fixture, and multiple fixtures are arranged in series on a DR2. This section shows the topology in terms of "height" of the LED chip stack.  For example:  a P023R6-660mA has a height of 3, a ceiling with 5 fixtures in series would then have a height of 15.  Should the DR2 calculate the wrong height - it can be corrected here. A P023R6-48v or E26-48v has a height of 14, 16, 17 or 18.  Do not adjust this for "48v" or "51v" devices!     Also - if there is any doubt about the operation of the DR2 - the "Reset rung count" button ( without changing the height values) will force a recalibration. Try that before changing any height values.
AL-WS-8B Common Features ( for all buttons) The AL-WS-8B is called a keypad or multi switch On DALI Devices you set the brightness of the status LEDs, the ontime of the status LEDs, and the name of the multi switch. Normally it should be hidden from Hue The "Fade UP" is the number of seconds that the blue status light stays on after a button is pressed.   if "90" is selected - the light will stay on all the time The max level slider controls the brightness Other controls have no effect
AL-WS-8B Features ( for each buttons) There are three multi address devices AL-WS-8B 1 to 8 buttons to assign to any function 1 to 8 small status leds for each button AL-DALI-IO16 8 PWM capable output drivers      300 mA each      60 volts      DC or AC switching      PWM dimming supported 8 USB / contact inputs      detect 5 to 24 volts input status      detect contacts AL-Relay8      8 On/Off relay outpus      1000 mA      60V      AC or DC