Home / public / ATX LED Products / AL - WS - DR2W | AL WS DR2C | AL WS DR2L

AL - WS - DR2W | AL WS DR2C | AL WS DR2L




 2 channel LED switch / driver  with WiFi Option

Front    Back IMG_9371 IMG_9375


Specifications - Base
  • Operates simply without WiFi - stand alone - or upgrade to WiFi
  • Wide paddle rocker switch with Up/Down or Momentary options
  • slider dimmer
  • on board micro for low dim and channel balance and tunable white
  • 2 channels with 24/30 watts each, 660 mA, low dim
  • N-Way input with remote dimming and 3-Way operation
  • backer board defines option modes (sense active/passive connection on pins 1 and 2)
    • 2 by 4 LEDs - 8 total, 48 watts single color, all same dimming level
    • 5 LEDs, tunable white, 30 watts
    • 5 LEDs - one FAN - independent controls
    • 8 LEDs - independent controls
Mode
feature
 number of LEDs
Wiz Module
pin 1
pin 2
AL-WS-DR2C
Dual Control
2 x 4
-
open
open
AL-WS-DR2C
Light+Fan
4
-
open
10K pull down
AL-WS-DR2C
simple
8
-
10K pull down open
AL-WS-DR2C
CCT
 4 (CCT)
-
10k pull down
10k pull down
AL-WS-DR2L
Dual Control
2 x 4

open
open
AL-WS-DR2L
soft + Fan
4

open
.1 uF Cap
AL-WS-DR2L
soft on
8

.1 uF cap
open
AL-WS-DR2L
soft on
4 (CCT)

.1 uF cap
.1 uF cap
AL-WS-DR2W
WiFi
8
DW
Active
open
AL-WS-DR2W-TW
WiFi
4 (CCT)
CCT
Active
Active

AL-WS-DR2 standard
  • both outputs drive to the same level

CCT mode
  • 5 tunable white LEDs - 30 watts
  • Color adjustable locally
  • Remote dimming and 3-way


Bath mode - Fan and Light
  • 5 LEDs (one color) - 30 watts
  • 1 12v DC fan with 12 watts
  • LEDs from main switch
  • Fan from N-Way input - timer option

Dual mode - 2 independent light strings
  • Each control can be On/Off or Momentary
  • 4 LEDs - 24 watts from main switch with slider dimming,
  • 4 LEDs - 24 watts from external simple switch with momentary dimming
    • if dry contact - Open = ON, wire Alarm Contact + any switch in series, no dimming, full output
Low Light
  • 4 or 8 LEDs 
  • Main switch On/Off/Dim
  • N-Way input - open (high) sets to 5% dim
WiFi / Alexa / Google Control
  • Philips Wiz module plug-on adapter
  • Tunable white ( 5 LEDs) or single color ( 8 LEDs)
  • Full control by App or Voice
Sample - 21 June 2019 v0
  • unit shipped had N-Way disabled by compile setting error
Sample - 10 July 2019 v1
  • Added power on/off for ESP12s
  • Added DIM/CCT for tuneable white
  • Fixed N-Way software
  • Added fan mode
  • op amp buffer
,
Wiz Setup steps ( July 2019 )
  • install the Wiz App from the Apple store  here
  • install the Amazon Wiz skill  here
  • click to select a room
  • turn AL-WS-DR2W power off
  • click to add a device
  • apply power and wait for 60 seconds
  • device should appear
  • set fade to 0 both up and down
  • set brightness default to lowest
  • use the wiz app to control and assign a name
  • add device using Alexa ( Alexa discovery)
  • control by Alexa works
Wiz Connectivity
today
wish list
SSID found
all works fine
fine
SSID not found - pristine
usually works
AP mode after 10 minutes
SSID not found - recycle
difficult - 4 steps
AP mode after 3 minutes
stay in AP mode until pairing complete
3 minutes step 1
wait for pairing to fail
App: button for normal   pairing
10 minutes
step 2
attempt 3 cycles
App: Button for manual pairing AP mode
10 minutes
step 3
attempt 5 cycles

10 minutes
step 4
attempt manual mode







     RSS of this page